Single acting pneumatic cylinder operation using 3/2 direction control valve.

Problem Description: -

The operation of Single acting pneumatic cylinder by using two pushbuttons PB1 and PB2. PB1 is for start the operation and PB2 is for stop the operation.

Diagram: -

Here we took Single acting cylinder and 3/2 single solenoid spring return valve now we have to use electric circuit to operate solenoid.

 

Program: -

Here is PLC program for making START/STOP pneumatic cylinder operation using PLC.

 

List of Inputs/Outputs

List of Inputs

X0: -PB1

X1: -PB2

List of Outputs

Y0: -Cylinder Relay output

Ladder Diagram for single acting pneumatic cylinder operation using 3/2 direction control valve.

Program Description: -

-In the ladder diagram, we use two push button one for start (PB1) and other one to stop (PB2). And we also use relay for operate solenoid as shown in figure.

-We give direct 24 voltage to PB1 (NO) and then PB1 normally open contact to PB2 (NC) and then PB2 normally closed contact to the relay.

-Now we take one normally open contact of relay and give to the PB2 common to give continuous supply to the relay it is called latching and take second normally open contact of relay to the solenoid and give 0v to solenoid to complete circuit.

-Now when we press PB1 power supply to the relay and relay start. And by starting relay solenoid is also get power and operate valve. Now if we release PB1 but power to the solenoid will not stop because of latching.

-Now when we press PB2 contact will open stop the relay that’s why solenoid is also stop and cylinder will back at their normal position because of spring return valve.

                                                                                    By Mansuri Afnan

Sequential lamps operation using PLC

This is a PLC program for the sequential lamp operation.

Problem description: -

Write PLC program to operate lamps in sequential mode using ladder diagram Language.

 Problem diagram: -

Solution: -

Here in this system, there are two lamps, two bush buttons which are connected to the PLC.

 The bush buttons are connected to the PLC inputs and lamps are connected to the Outputs of the PLC.

There are following condition for the system to work which are as follows: -

1)    When START PB is to be pushed lamp1 should start and lamp 2 should start after 5 seconds of lamp1.

2)    When STOP PB is to be pushed both the lamps1&2 are to be stopped.

 Now to meet the following conditions we have use a timer which delay the operation of lamp2. 

List of inputs/outputs: -

Inputs: -

1)     X0 -Start PB

2)     X1 -Stop PB

Outputs: -

1)     Y0 -Lamp1

2)     Y1 -Lamp2

Ladder diagram for the sequential operation of the lamps.

Program Description: -

-In Rung we used STRAT PB (X0) to start LAMP 1 (Y0). Here we used NC contact of STOP PB (X1) to stop the LAMP 1(Y0). In parallel of X0 contact we used NC contact of Y0 to latch the output.

-In second rung we used Timer T1 to count the delay for the LAMP 2 (Y1).

-In rung 3 we used NO contact of T1 so once time delay over the LAMP 2 (Y1) will on.

 

                                                                                              By Naisarg Prajapati

Double acting Cylinder Forword/reverse operation using PLC.

 Double acting Cylinder Forword/reverse operation using PLC.           

This is the PLC program for double acting cylinder operation using PLC.                                                              

Although writing a PLC program in Double acting cylinder is a highly technical process, it can be understood in simple language:

Problem Description: -

We need to operate double acting cylinder using PLC. Write the PLC program using ladder diagram language and draw pneumatic circuit.

 

Problem Diagram: -

Solution: -

Here we need to operate double acting cylinder with PLC. As show in figure we took two push buttons for forward and reverse operation. PLC is used to control the outputs. We used double solenoid direction control valve for forward and reverse operation of the cylinder. Once user will press forward button, cylinder will move forward and if user presses reverse button, cylinder will move reverse.

Here we used PLC for output control so need to write program in PLC according to application.

 Program

Here is PLC program for making forward/reverse cylinder operation using PLC.

 

List of Inputs/Outputs

List of Inputs

X0: -Cylinder Forward

X1: -Cylinder Reverse

List of Outputs

Y0: -Cylinder Forword

Y1: -Cylinder Reverse

 

Ladder Diagram for forward/reverse operation of double acting cylinder.

Program Description: -

-        In first rung we have used NO contact of the Cylinder forward push button (X0) so Cylinder forward (Y0) output can be operated with the forward push button (X0).

-        In first rung we have used NO contact of the Cylinder reverse push button (X1) so Cylinder reverse (Y1) output can be operated with the reverse push button (X1).